It's go time! The patterns will be at the foundry in California by the end of February & the pour happens in March!
Save $200 by pre-ordering now!
March 15th is the deadline for pre-orders!
Only pre-orders will be individually numbered ie- #4 of 25
Click products>Cylinder Heads>Add to Cart
Heads will be shipped no later than July 1, 2018!
I have two pre-orders for Dodge Brothers four banger heads, so when I take the six cylinder patterns to the Edelbrock foundry later this month, I'm going to take this pattern along as well. This is a probably a one-time only run, so if you're interested, I need to know NOW. Please email me at email@example.com if you are interested. Due to the very small quantity, they won't be inexpensive, and depending on the year of your engine, they may require extensive additional machining for distributor, water neck, fan bracket, etc. The level of bolt-on-ability will be up to you, and priced accordingly. We can provide anything from a raw bare casting to a ready-to-bolt-on head.
The design is identical to the Montana Dodge Boys Fast Four Special Bonneville roadster Gen III head, and has been tested on the flow bench and proven on the Salt.
Please spread the word and share as this is a one shot deal! Thanks - Pedro - firstname.lastname@example.org
News Flash! There has been sufficient interest in EDGY heads for 25" blocks (Chrysler/DeSoto) to commit to casting both 23 and 25 inch heads at the same time. Stay tuned, the website will be updated for pre-ordering this week!
Update on the 230 for the 1933 Dodge Peking to Paris Rally car build!
Tony Smith spent the weekend working on the 230. Here are his notes-
It was quite clean inside and in amazing condition overall. There were no signs that the engine had ever been disassembled. The oil pan had a bit of sludge in the bottom as they always do, but unlike most of these old engines that I tear apart it didn't have sludge accumulated everywhere else. Even the oil reservoirs adjacent to the lifters were clean! Here are the details:
- Fully disassembled the engine.
- Rod and main bearings all showed normal wear patterns. Main thrust bearing surface was good.
- Piston wear patterns were centered and normal.
- Thermally processed the block, pan, timing cover, front plate, etc.
- Bead blasted the main caps and stock main bolts.
- Deburred and buffed the main cap mating surfaces and chased the main cap threads in the block.
- Checked main caps' fit in the block's registers. All caps fit tightly.
- Torqued the main caps on with stock fasteners.
- Shotpeened the block.
- Hot tanked the crank and rods.
- Shotpeened the crank.
- "Polished" the rod beams to remove lateral stress risers from the forging die parting line.
- Torqued up the rods with the stock rod bolts.
- Shotpeened the rods.
- Removed the stock rod bolts from the rods and ground the mating surfaces in preparation for resizing the big ends.
- Magnafluxed the block, crank, and rods. No cracks found!
- Inspected and measured the crank: rod and main journals are standard size with 0.001" wear and very mild grooving/scratching. Thrust surfaces are not worn. Rear main seal surface is good, not grooved by seal.
- Inspected and measured the block: cylinders are standard size with 0.003" wear/taper. No gouges or scratches in cylinders. Deck is flat and in good condition. Manifold surface is pitted and will need surfacing. Main bore is straight and within specs. Rear cam bore (the one that doesn't have an insert bearing) shows no signs of wear. No signs of valve seat erosion. No stripped threads in block but there are several broken head and manifold studs that will require drilling out. Lifter bores show no signs of wear.
- Inspected the cam. Journals are within specs. Lobes show normal wear patterns. Will be a good core for regrinding.
- Inspected the lifters. Faces have normal patterns showing good rotation. No wear on sides. Good cores for regrinding.
The opportunity to take on this exciting project is still less than a week old, yet we've already pulled the body, and the chassis and engine are enroute to the shop for teardown. It's going to be a busy weekend!
We're excited to be working with our Bonneville sponsor CP/Carrillo to create a set of lightweight, coated, forged pistons for Patrick's Peking to Paris build. These will have a modern ring pack and wrist pin, and work perfectly with stock rods. Once the design has been finalized, they will be available for 218/230s and 241/265s only through moparmontana.com
Chris dug through the engine pile out at the Ranch and found this beautiful standard bore 230 that will be the heart of the Peking to Paris build. Tony will be picking it up this week to take it to the machine shop to start the machine work!
We have been hired by a gentleman in Belgium to prepare this gorgeous TJ Richards-bodied 1933 Dodge roadster to compete in the 2019 Peking to Paris Rally. If not familiar, this arduous 8000 mile trek is truly something you must learn more about.